Breaking the dsi xl case in your Nintendo ds lite could be frustrating, but as much as harm to a Nintendo system goes, fixing a broken case is relatively cheap. Unlike internal damage, which in turn renders it useless, a broken case may be replaced, preventing you against requiring you to obtain a new unit. In case you have broken the situation with your Nintendo ds lite, but the system still works properly you'll be able to send the machine in for repair or else you are capable of doing it yourself.
Instructions
1. Cover your work surface with a soft covering such as a face towel. Lay the Nintendo ds lite facedown on the towel.
2. Peel the rubber pads through the back of the unit. If you possibly could’t get them program your fingers, you can use the tiny screwdriver to pry the pads up.
3. Exclude the screws on the back from the unit. The converter should have four screws holding it together: the one which holds in the battery inside lower right corner, one around the card slot and two on the left-hand side on the unit.
4. Take away the battery from your unit. Take away the screw in the battery compartment and lift off the quilt the screw was holding constantly in place. jklzaeqc 1122
5 . Lift a corner cover off the unit carefully once all of the screws are actually removed. Don’t pull too much, since the unit is attached by a few cables. Note the spot that the cables are connected to the rear case and carefully pull the end with the cables to clear out them from the back cover.
6. Unscrew the screws which can be holding the buttons about the front on the unit available. Support the black flap above the directional pad and pull the wire attached underneath the flap off the casing.
7. Detach the energy indicator by pulling left on the wire while sliding the casing toward the proper. The wire should slide beyond case plus the bottom level of the front in the case should come free, leaving the top, front perhaps the dsi xl cases in position.
8. Slide the wire about the left side of the top 1 / 2 of true from the casing. Lift the ring about the right side out from the case. This certainly will expose four rubber pads about the back from the screen.
9. Peel away the rubber pads to reveal four screws. Eliminate the screws at intervals of corner of the screen.
10. Keep the casing on spare on both of the screen and slide the casing up from the unit. The way it is should remain attached by a wire. Pull the wire left and push the casing directly to detach the wire from the casing.
11. Return back from the procedures in reverse order to collect the modern Nintendo dsi xl case ( http://www.vdealbox.com/dsi-xl-ll-accessories/dsi-xl-ll-housing-case-cover.html ) over the internal the main unit.
Instructions
1. Cover your work surface with a soft covering such as a face towel. Lay the Nintendo ds lite facedown on the towel.
2. Peel the rubber pads through the back of the unit. If you possibly could’t get them program your fingers, you can use the tiny screwdriver to pry the pads up.
3. Exclude the screws on the back from the unit. The converter should have four screws holding it together: the one which holds in the battery inside lower right corner, one around the card slot and two on the left-hand side on the unit.
4. Take away the battery from your unit. Take away the screw in the battery compartment and lift off the quilt the screw was holding constantly in place. jklzaeqc 1122
5 . Lift a corner cover off the unit carefully once all of the screws are actually removed. Don’t pull too much, since the unit is attached by a few cables. Note the spot that the cables are connected to the rear case and carefully pull the end with the cables to clear out them from the back cover.
6. Unscrew the screws which can be holding the buttons about the front on the unit available. Support the black flap above the directional pad and pull the wire attached underneath the flap off the casing.
7. Detach the energy indicator by pulling left on the wire while sliding the casing toward the proper. The wire should slide beyond case plus the bottom level of the front in the case should come free, leaving the top, front perhaps the dsi xl cases in position.
8. Slide the wire about the left side of the top 1 / 2 of true from the casing. Lift the ring about the right side out from the case. This certainly will expose four rubber pads about the back from the screen.
9. Peel away the rubber pads to reveal four screws. Eliminate the screws at intervals of corner of the screen.
10. Keep the casing on spare on both of the screen and slide the casing up from the unit. The way it is should remain attached by a wire. Pull the wire left and push the casing directly to detach the wire from the casing.
11. Return back from the procedures in reverse order to collect the modern Nintendo dsi xl case ( http://www.vdealbox.com/dsi-xl-ll-accessories/dsi-xl-ll-housing-case-cover.html ) over the internal the main unit.
RSS Feed