The Wiimote runs on the wireless signal, eliminating the requirement of a cord coupled to the console. It is possible to modify (or "mod") the electronics within the Wii so that it will activate an instant-fire mode. A modification kit have to be acquired at a game store or hobby shop. You simply must partially disassemble the Wii controller.
Instructions
1. Open it compartment lid around the back from the Wii Remote Remove the batteries. Take away the screws from inside the compartment while using the Tri-Wing screwdriver.
2. Get rid of the screws from your controller having a Phillips jeweler's screwdriver. Pull the 2 parts of the controller apart. Eliminate the circuit card from inside the wii controller.
3. Position the part of the controller that's the battery tab in the bottom about the work surface. Rotate the portion of the wii nunchuck so your tab is closest to you. Drill a hole over the button left corner, just above the screw hole, with an electric drill.
4. Insert the end in the switch connected to the modification chip into your hole. Apply bonding glue across the change to cement it into position. Put the chip, contact pins up, to the right and above the switch, against a protruding bit of plastic. Apply bonding glue round the chip to cement it into position. Allow glue set a great hour before continuing.
5. Position the circuit card within the work surface with the text right-side up. Locate the horizontal white strip while using six numbers close to the the top board. Draw an imaginary line on the second number within the left down the board. Locate the contact that intersects this line that is certainly with the upper left corner on the circle with the "X" inside of it. Solder the conclusion from the yellow wire coupled to the chip to this contact. Permit solder cool for just two minutes.
6. Locate both contacts alongside the amount "055" about the board. Rotate the plug-in so the number is inverted. Solder the end in the red wire connected to the chip for the contact next to the number. Solder the end on the green wire coupled to the chip for the contact beside usually the one just soldered. Permit solder cool for a few minutes. Unplug the soldering iron.
7. Reassemble the circuit board inside wii controllers Position the two parts of the controller ( http://www.vdealbox.com/wii-accessories/wii-controller.html ) together again. Reattach the screws. Reinsert the batteries and close the lid.
Instructions
1. Open it compartment lid around the back from the Wii Remote Remove the batteries. Take away the screws from inside the compartment while using the Tri-Wing screwdriver.
2. Get rid of the screws from your controller having a Phillips jeweler's screwdriver. Pull the 2 parts of the controller apart. Eliminate the circuit card from inside the wii controller.
3. Position the part of the controller that's the battery tab in the bottom about the work surface. Rotate the portion of the wii nunchuck so your tab is closest to you. Drill a hole over the button left corner, just above the screw hole, with an electric drill.
4. Insert the end in the switch connected to the modification chip into your hole. Apply bonding glue across the change to cement it into position. Put the chip, contact pins up, to the right and above the switch, against a protruding bit of plastic. Apply bonding glue round the chip to cement it into position. Allow glue set a great hour before continuing.
5. Position the circuit card within the work surface with the text right-side up. Locate the horizontal white strip while using six numbers close to the the top board. Draw an imaginary line on the second number within the left down the board. Locate the contact that intersects this line that is certainly with the upper left corner on the circle with the "X" inside of it. Solder the conclusion from the yellow wire coupled to the chip to this contact. Permit solder cool for just two minutes.
6. Locate both contacts alongside the amount "055" about the board. Rotate the plug-in so the number is inverted. Solder the end in the red wire connected to the chip for the contact next to the number. Solder the end on the green wire coupled to the chip for the contact beside usually the one just soldered. Permit solder cool for a few minutes. Unplug the soldering iron.
7. Reassemble the circuit board inside wii controllers Position the two parts of the controller ( http://www.vdealbox.com/wii-accessories/wii-controller.html ) together again. Reattach the screws. Reinsert the batteries and close the lid.
RSS Feed